Skip to main content

1. TRANSPORTATION AND INSTALLATION

1.1.TRANSPORTATION

image.png

Turn each axis to transportation gesture before move the robot and be sure to keep the gesture during transportation until it be properly installed and mounted. Transportation gesture of each axis is shown below. Perform the transportation properly, or it may result in personnel injury or equipment damage.

image.png

Refer to theoretical weight of main parts shown below to install, disassemble and transport the robot.

image.png

image.png

image.png

A support plate is needed for transporting ER500-2800 robot, as shown in the figure below. Remove the plate before installing the robot.

image.png

1.1.1. Transport by a forklift
This model of robot can be handled by forklift. Before handling, install the screws of the forklift fixing plate on the robot transfer seat (ER280-3200-CE, ER350-3200-CE robot 4 forklift fixing plates, 8 M16X45 screws; ER350-3300-CE, ER500-2800-CE, ER600-2800-CE, ER700-2800-CE, UNO-700-2800-AC-CE robot 2 forklift fixed plates, 8 M16X40 screws), forklift forks into the fixed plate for handling. Before handling the robot, it must be confirmed that all the fixing bolts of the robot have been removed. After handling, remove the forklift fixing plate.

image.png

 

image.png

image.png

 

image.png

image.png

 

1.1.2. Transport by a crane
The robot described in this manual can be transported by a crane. Fix four M24 rings on the robot rotation base, use a crane and strings to heave the robot. Make sure that the strings are fixed as shown in the figure below.
Take necessary measures to avoid paint peeling due to collision between the strings and the robot.

image.png

image.png

image.pngFig 1.7 Use a crane to transport the robot (ER350-3200-CE)

image.pngFig 1.8 Use a crane to transport the robot (ER500-2800-CE, ER600-2800-CE, ER700-2800-CE, UNO-700-2800-AC-CE)

image.png

 

1.2.Storage
This series of robots is usually transported on wooden pallets, and its storage space requirements are as follows:

image.png

 

1.3.Installation

image.png

The following precautions must be fully understood and observed before installing the robot.
 Be sure to read and understand SAFETY chapter thoroughly.
 ESTUN robots must be transported, mounted and operated by authorized person, and in accordance with the applicable national laws, regulations and standards.
 Check the external damage of the robot package. Open the package and check the external damage of the robot.
 Make sure the weight of the robot is within the forklift or crane load capacity. Details see Section 1.1 TRANSPORTATION.
 Storage and mounting condition should be complied with Section 1.3 INSTALLATION CONDITION.

image.png

image.png

Fig 1.11 Robot base force

image.png

image.png

 

image.png

Fig 1.4 Robot base mounting dimension (ER280-3200-CE, ER350-3200-CE)

image.png

image.png

image.png

image.png

Fig 1.6 Robot mounting plate dimension and mounting method (ER280-3200-CE, ER350-3200-CE)

image.png

1.4.Installation conditions

image.png

image.png

image.png

 

Performance of resistant chemicals and resistant solvents.
(1) The robot cannot be used with the following liquids. Potentially these liquids will cause irreversible damage to the rubber parts (such as gaskets, oil seal, O-rings, etc.) (As exception to this only liquids approved by ESTUN can be used with the robot).
(a)organic solvents
(b)cutting oil including chlorine/gasoline
(c)amine type detergent
(d)acid, alkali and liquid causing rust
(e)other liquids or solutions that will harm NBR or CR rubber
(2) When the robot works in the environment using water or liquid, complete draining of J1 base must be done. Incomplete draining of J1 base will make the robot break down.
(3) Do not use unconfirmed liquid.
(4) Do not use the robot immersed in water, neither temporary nor permanent. Robot must not be wet permanently. Example, in case motor surface is exposed to water for a long time, liquid may invade inside the motor and cause failure.