Skip to main content

SAFETY

This chapter describes the precautions which must be followed to ensure the safe use of the robot. Before using the robot, be sure to read and understand this chapter thoroughly. ESTUN robots must be transported, mounted and operated in accordance with the applicable national laws, regulations and standards. Appropriate safeguards must be correctly situated to protect the users.
Before using (mounting,operating,maintaining, repairing) the robot, be sure to read and understand this manual and its relevant manuals. Be sure to have familiarization with the knowledge of robot system and the safety precaution. Even if all instructions are followed, this is not a guarantee that the robot will not cause personal injuries or material damage.

DEFINITION OF USER

The personal can be classified as follows
 Operator
Turns the robot controller power on/off.
Starts the robot program from operator panel.
 Programmer
Operates the robot.
Teaches the robot inside the safety zone.
 Maintenance engineer
Operates the robot.
Teaches the robot inside the safety zone.
Maintenance (repair, adjustment, replacement)
Operator is not allowed to work in the safety zone.
Programmers and maintenance engineers can work in the safe area.
During the operation, programming, and maintenance of the robot system, the programmer, operator and maintenance engineer should take additional care of their safety by wearing the following safety items.
 Adequate clothes for operation
 Safety shoes
 A helmet

SPECIAL TRAINING

Tasks in the safety zone including transportation, teaching, calibrating, repairing, etc.
Have the operator attending the training courses before using the robot system.
For more information on training, please consult Nanjing ESTUN Robotics Engineering Co., Ltd.

SAFETY NOTATIONS

If the contents of the following symbols appear in this manual, the user must read them carefully and strictly abide by them.

image.png

SAFETY OF THE USER

(1) The robot should be transported and installed by accurately following the procedures recommended by ESTUN. Wrong transportation or installation may cause the robot to fall, resulting in severe injury or damage.
(2) Draw an outline on the floor, clearly indicating the range of safety zone before install the robot. If necessary, install a safety fence or warning board to ensure the safety operation of the robot and keep unauthorized person outside the safety zone.
(3) Never hang any items above the robot. Failure to observe this caution may result in injury or equipment damage.
(4) Never lean on the controllers, and avoid inadvertently pushing buttons. Failure to observe this caution may result in injury or damage by unexpected movement of the manipulator.
(5) Take precaution for falling parts when disassemble the robot.
(6) When adjusting each peripheral equipment independently, be sure to turn off the power of the robot.
(7) The peripheral equipment must be grounded.
(8) In the first operation of the robot after installation, the operation should be restricted to low speed. Then, the speed should be gradually increased to check the operation of the robot.
(9) Operators should be ungloved while manipulating the operator panel or teach pendant. Operation with gloved fingers could cause an operation error.
(10) Programs, system variables, and other information can be saved on memory card or USB memories. Be sure to save the data periodically in case the data is lost in an accident.
(11) Never forcibly move the robot axes. Failure to observe this caution may result in injury or equipment damage.
(12) Take precaution when wiring and piping between the controller, the robot and the peripheral equipment. Run the piping, wiring, or cables through a pit or use a protective cover, so that they are not stepped on by personnel or run over by forklift.
(13) Any robot in working condition may cause severe personnel injury or equipment damage due to unexpected moving. Test must be performed on each safety measure (safe door, brake, safe indicators, etc.). Before turn on the system, make sure that no one is in the working space.
(14) Never set motion range or load condition that exceeds the range indicated in specification table. Incorrect setting may result in personnel injury and equipment damage.
(15) Observe the following precautions when performing teaching operations within the working space of the robot:
 Do not enable the system unless the mode is switched to manual, and make sure that all autocontrol is cut off.
 Speed must be limited under 250mm/s at manual mode. Only authorized person with fully understand of the risks can adjust the robot to rated speed manually.
 Be careful about rotating joints to prevent hair and clothes involved. Take precautions of injury or damage caused by the manipulator or other auxiliary devices.
 Check the motor brake to avoid personnel injuries caused by unexpected situation.
 Always have an escape plan in mind in case the robot comes towards you unexpectedly.。
 Ensure that there is a place to retreat to in case of emergency

image.png

image.png

SAFETY OF THE OPERATOR:
(1) Before operating the robot, press the EMERGENCY STOP on the front door of the electric cabinet and the upper right of the teaching pendant to check whether the indicator light of “SERVO ON” is off and confirm that power supply is turned off.
(2) Never allow unauthorized personnel to touch the controller during operation. Failure to observe this precaution may result in unexpected movement of the robot, severe injuries and material damage.
(3) When attaching a equipment to the robot, be sure to turn off the power of the controller and the peripheral equipment, and display a warning sign. Turning the power on during equipment installation may cause electric shock or injury due to unexpected movement of the robot.
(4) Emergency stop
Emergency stop is an external button of the controller that can stop all the robot operation.
When emergency button is pressed, the power of the robot (except the power of the servo) is cut off. The system will not run unless the pressed emergency button being released and the system being turned on

image.png

SAFETY OF THE PROGRAMMER:
While teaching the robot, the programmer must enter the robot operation area. The programmer must ensure the safety especially.

image.png

To use the teach pendant safely, the following precautions should be taken:
 Be sure that the enable switch is effective at any time.
 Enable switch must be turned off when pausing, programming or testing the system.
 Teach pendant must be taken with the programmer when performing teaching jobs in the work space, to avoid inadvertent operation by unauthorized person.
 Teach pendant must not be left within the work space of the robot, as injury or damage can occur if the robot comes in contact with the teach pendant.

SAFETY OF THE MAINTENANCE:
(1) Pay attention to the parts that are prone to heat in the robot
Some parts of the robot are heated when the robot is operating, especially the servo motor and reducer.
If a maintenance user needs to touch such a part in the heated state, the user should wear heatresistant gloves or use other protective tools

image.png

(2) Safety Precautions for Disassembling Parts
Open the cover or shell only after interior parts such as gears are not moving any more. Never open the cover or shell when the gear or bearing is moving. Use auxiliary device to keep interior part to its position.
Observe the following precaution when performing the first test after installation, inspection or maintenance:
a) Clear tools to proper locations outside of the working space of the robot.
b) Make sure that all precaution measures are available.
c) Make sure that there is no one in the working space of the robot.
d) Pay special attention to working condition of the maintenance parts when performing test.
Never use the manipulator as a ladder when performing maintenance. Never climb on the robot to avoid falling.
(3) Safety Precautions Regarding Pneumatics/Hydraulics
There may be air/liquid residue in the system when the air pump or hydraulic pump is turned off.
Before checking the pneumatic or hydraulic parts, release remaining pressure from the system to avoid personnel injury or equipment damage.

image.png

(4) Although the power supply needs to be turned on for fault diagnosis, be sure to turn off the power supply and disconnect other power connections when servicing the robot.
(5) Brake detection
Brake may be wearing in daily operation. So brake inspection should be performed by the following procedure:
a) Move each joint to the position where the joint bears maximum load.
b) Turn off the robot. The brake works.
c) Mark each joint.
d) Check if the joint moves over a period of time.
(6) Safety precautions when adding lubricating oil
Personnel injury or equipment damage may occur during greasing. Observe the following precautions before greasing.
 Take additional care of safety by wearing safety items (such as gloves) to avoid injury from heated oil or reducer.
 Open the oil chamber with special caution and keep away from the opening. Oil may spray due to oil pressure.
 Feed the oil according to required quantity and never fill up the oil chamber. Check the oil indicator when finished.
 Never mix different types of oil into one reducer. Clean remained oil thoroughly before changing another type.
 Oil draining must be performed thoroughly. Check the oil indicator when finished

image.png

 

SAFETY OF THE TOOLS AND PERIPHERAL 

Peripheral device may still be running even after the system has been turned off. Personnel injury may occur due to damaged power lines.

 

ROBOT SAFETY

For abnormal or emergency situations, e.g. persons trapped in or pinched by the robot, the robot axes should be moved. (Contact ESTUN for more details about dismantling).
Small robotic arms can be removed manually, but larger robots require a crane or other small equipment.
Before releasing the joint brake, the mechanical arm must be fixed first to ensure that the mechanical arm will not cause secondary injury to the trapped person under the action of gravity.

 

STOP TYPE OF ROBOT

The following three robot stop types exist:

Power-off stop
Servo power is turned off and the robots stops immediately. Servo power is turned off when the robot is moving, the path of the deceleration in uncontrolled.
The following processing is performed at Power-off stop:
 An alarm is generated and servo power is turned off immediately
 Pause the running program
Frequent Power-off stop of the robot during operation can cause failures of the robot. System configurations in which a power outage stops under normal circumstances should be avoided.

Alarm stop
This is a robot stop method that decelerates the movement of the robot to a stop with a control command after the robot system issues an alarm (except for a power failure alarm).
By controlling the stop, the following processing is performed:
 An alarm (not include power-off alarm) is generated due to overload, system faulty, etc.
 The servo system issues a “control stop” command, decelerates to stop the robot, and suspends the execution of the program.
 Disconnect the servo power.

Hold
The robot is decelerated until it stops, and servo power remains on.
The following processing is performed at Hold:
 Decelerates the motion of the robot to a stop, and suspends the execution of the program.

 

Warning and caution labels

(1) Electric shock warning sign

image.png

This label indicates hazardous voltage or electric shock.

(2) High-temperature Warning

image.png

The area where this label is attached will heat up, so be careful. Wear heat-resistant gloves and other protective equipment when you must touch the device in a hot state.

(3) No Step-on Warning

image.png

Do not put your feet on the robot or climb on it. Stepping on it will cause adverse effects on the equipment and may also cause injury to the operator.

 

(4) Personal injury warning

image.png

There is a risk of being injured by the robot when working within the robot's motion range.

(5) Disassembly is prohibited

image.png

The parts with this mark are not allowed to be disassembled by the user. Disassembly should be carried out by professionals using professional tools.

(6) Energy storage warning

image.png

The balance cylinder is equipped with spring, high pressure gas or high pressure liquid, and it is strictly forbidden to disassemble it without permission

(7) Transport Position Label

image.png

image.png

This mark indicates precautions for handling robots.