Advanced Search
Search Results
651 total results found
9. Tryb kontroli pozycji z wejść impulsowych
Pn005.1=1 tryb kontroli pozycji z wejść impulsowych 9.1 Idea sterowania impulsowego (w szczególności w trybie krok/kierunek) Pn004.2 - wybór rodzaju sterowania impulsowego. W przypadku krok/kierunek, należy ustawić wartość na 0.Sterowanie w trybie krok/kier...
10. Tryb kontroli z wewnętrznego pozycjonera
10.1 Konfiguracja trybu wywoływania kroków pozycjonowania Gdy skonfigurowano serwonapęd Estun w tryb pracy, jako sterowanie z wewnętrznego pozycjonera (Pn005.1=C), za sposób sterowania wykonywaniem wewnętrznych kroków odpowiadają ustawienia podparametrów param...
11. Komunikacja z napędem w protokole ModBus
11.1 Konfiguracja parametrów portu szeregowego RS485 oraz protokołu komunikacyjnego Protokół komunikacyjny MODBUS może być użyty tylko wtedy, gdy Pn700.2 jest ustawiony na 1. Istnieją dwa sposoby komunikacji MODBUS: ASCII oraz RTU. Mapowanie stanów wejść dysk...
12. Lista parametrów
13. Dobór serwosilnika do aplikacji
13.1. Czynniki brane pod uwagę podczas doboru serwosilnika do aplikacji Czynniki brane pod uwagę przy wyborze serwomechanizmu: 1. Obciążenie mechanizmu 2. Profil ruchu 3. Prędkość osiągane z obciążeniem 4. Dokładność pozycjonowania 5. Środowisko użytkowania Sp...
Weintek-FAQ
Przebudowana struktura po imporcie Outline dla marki Weintek
1. Notes on USB Cable
The following are some important points relevant to USB cable:HI-SPEED USB Revision 2.0 SHIELDED 24AWG 1. The PC must support USB 2.0 or USB 3.0.2. Use a double shielding USB cable: Foil+ Braid Shield. 3. The length of the cable should be limited to less than...
2. Portrait Display on HMI
If the project file is edited in portrait mode, the following settings help todisplay project correctly on HMI. A.Step 1. On HMI, open [System settings] » [OS setting], and select [90] or [270] in Portrait Mode group box.Applicable models: eMT, iE, XE, mTV, i ...
3. Customize Startup Screen
The startup screen on HMI can be customized, for example, putting the trademark logo. The following steps show how to do that. Please note that this feature is not available for cMT Series.For i Series HMI, this feature is only available for firmware version 2...
4. MT8000/6000 Touch Panel Adjust and System Initialization
Switch SW1 to ON position (as shown in picture 1). Press “Reset” or re-plug in the HMI. Picture 1 2. Touch panel calibration screen is shown as follows. Put the HMI screen perpendicularly to your line-of-sight, and point your finger at the center of the cr...
5. Speed Up the Display Rate on MT8000
When a large image is displayed, for example, using a 65536 color image as background image may cause the HMI process speed to slow down. Users can follow the instructions below to speed up the display rate of image. Step 1While using an image file as backgr...
6. Update the MT8000/6000 OS
MT8000/6000 OS Image version is 20081013 or later, which supports using USB disk or CF card to update OS. The update process is similar to downloading project to the touch panel HMI. The following example shows how to update OS by using USB disk. 1. Find the c...
7. Change Model of Project
The following example shows how to change a MT8070iE (800 x 480) project to an eMT3120 (1024 x 768) project. Step 1. Open the MT8070iE project.Step 2. Click [Edit] button » select [System Parameters] » [Model] tab » select [eMT3120/eMT3150 (1024 x 768)] Step ...
8. Translate MT500 Project to MT8000
How to translate projects for MT500 model to MT8000/eMT3000 model EasyBuilder provides a feature to translate project files used on MT500 models and download them to MT8000/eMT3000 models. In this way, the project files can be upgraded without being rebuilt. T...
9. How to Decompile the xob file which uploading in the USB Disk
1. Upload the program file of the HMI to the USB disk, and then copy it to the PC (or use the file on the USB disk directly)2. Check out the file that was previously copied from the HMI in the file browser. The original file doesn’t have extension file name. ...
10. Display Chinese Fonts
How to display Chinese characters correctly? When you open a project that contains Chinese characters, you may find that the characters are displayed as shown in the following figure The following steps will show you how to solve this problem.Step 1. Go to Sy...
11. Ethernet Pass-Through Communication
MT8000 provides Ethernet pass-through communication which allows PC to link to the PLC through the HMI. In this situation, the role of HMI is similar to a converter. First, a virtual serial port must be created on PC. The application program on PC can commun...
12. How to Setup the Printer
The following are the instructions for setting up the printer (take HP printer for example):1. Setup the printer: Run EasyBuilder Pro, select “Edit / System Parameters”; 2. Switch to the “Model” tab, select the printer type: HP PCL Series (USB) and setup the ...