Advanced Search
Search Results
888 total results found
4. Conversion factors (factor group)
Servo controllers will be used in a huge number of applications: As direct drive, with gear or for linear drives. To allow an easy parameterization for all kinds of applications, the servo controller can be parameterized in such a way that all values like the ...
5. Position control function
This chapter describes all parameters which are required for the position controller. The desired position value (position_demand_value) of the trajectory generator is the input of the position controller. Besides this the actual position value (position_actua...
6. Device control
The following chapter describes how to control the servo controller using CANopen, i.e. how to switch on the power stage or to reset an error 6.1 State diagram (State machine) Using CANopen the complete control of the servo is done by two objects. Via the cont...
7. Control mode
ProNet/EDS/ETS currently supports 5 control modes in CANopen DSP402:HOMING MODEPROFILE VELOCITY MODEPROFILE TORQUE MODEPROFILE POSITION MODEINTERPOLATED POSITION MODEThis chapter mainly describes four control modes as 7.1 Relevant parameter of control mode ...
8. Parameters of the CAN interface
Notes:EDS,ETS and ProNet use the same node.These parameters is appropriate for each axis of EDS and ETS.
9. CAN communication example
The entire test below is based on three conditions:1. Communication has been established correctly.2. The address of the servo drive is 1.3. All the message data is hexadecimal. 9.1 SDO configuration SDO operation is to read and write parameters (0601h host ...
10. Other function
10.1 Digital inputs and outputs60FE (Physical outputs)In some case, the switch (homing and limit switch) is committed by upper computer not servo drive.the signal is committed by object 60FE-01h(Physical outputs). Bit16-bit23 of the object corresponding inpu...
Appendix Object dictionary
Note: * is used for ProNet-□□AMG only
ESTUN – ED3L (Summa) – AC Servodrive with Pulse References Product Manual
Instrukcja serwonapędów AC ESTUN Summa serii ED3L sterowanych sygnałami impulsowymi.Zawiera: opis napędu, instalację, okablowanie i podłączenia, ustawienia podstawowe, funkcje aplikacyjne, komunikację CANopen i Modbus, uruchomienie próbne, strojenie, alarmy, p...
About this Manual
PurposeThis manual provides the information required for the Selection, Wiring, Connection, Settings, Trial Operation, Tuning and Functions of the Summa ED3L Series AC Servo Drive with pulse references (referred to as ED3L).Read and understand this manual to e...
Safety Precautions
General Precautions Storage Precautions Installation Precautions Wiring Precautions Operation Precautions Maintenance Precautions Disposal Precautions
1. ED3L Servo Drive
1.1 Product FeaturesAs a new single-axis AC servo product from ESTUN, ED3L is designed with its excellent performance and practical control functions to create a complete set of solutions with the best cost performance for customers.Matching with the EM3A, EMG...
9. MODBUSCommunications
9.1 Communication WiringThe connection terminals CN3-IN and CN4-OUT are used for MODBUS communications. 9.2 Setting Communication Parameters 9.3 MODBUS Communication ProtocolMODBUS communication protocol is only used when Pn700.2 is set to 1. There are t...
2. Installation
2.1 Installation Precautions Installation Near Sources of HeatImplement measures to prevent temperature increases caused by external heat sources so that the ambient temperature of the Drive is within the specified limits. Installation Near Sources of Vibrat...
3. Wiring and Connecting
3.1 Precautions for Wiring3.1.1 General Precautions 3.1.2 Countermeasures against Noise Since the Drive uses microprocessors, it may be affected by switching noise from peripheral devices.To prevent the noise from the Drive or the peripheral devices from c...
4. Basic Settings
You can implement the functions of parameter setting, display, monitoring, alarm, adjustment, etc. of the Drive in the following two ways. Use the Panel Operator of the Drive Use the ESView V4 (Recommended) 4.1 Panel Operator4.1.1 Key Names and FunctionsTher...
5. Application Functions
5.1 Power SupplyThe main circuit and control circuit of the Drive can be operated with AC power input. When AC power input is selected, single- phase or three phase power input can be used. You shall to set the parameter Pn007.1 and Pn007.3 (use AC power input...
6. CANopen Communication
6.1 Wiring and ConnectionConnection diagram Terminal arrangement Signal DefinitionThe external communication connection terminals (CN3-IN and CN4-OUT) are of RJ45 connectors. The interface line as the master or controller is connected from CN3-IN, and CN4...