Search Results

13.1. Czynniki brane pod uwagę podczas doboru serwosilnika do aplikacji Czynniki brane pod uwagę przy wyborze serwomechanizmu: 1. Obciążenie mechanizmu 2. Profil ruchu 3. Prędkość osiągane z obciążeniem 4. Dokładność pozycjonowania 5. Środowisko użytkowania Sp...

The following are some important points relevant to USB cable:HI-SPEED USB Revision 2.0 SHIELDED 24AWG 1. The PC must support USB 2.0 or USB 3.0.2. Use a double shielding USB cable: Foil+ Braid Shield. 3. The length of the cable should be limited to less than...

If the project file is edited in portrait mode, the following settings help todisplay project correctly on HMI. A.Step 1. On HMI, open [System settings] » [OS setting], and select [90] or [270] in Portrait Mode group box.Applicable models: eMT, iE, XE, mTV, i ...

The startup screen on HMI can be customized, for example, putting the trademark logo. The following steps show how to do that. Please note that this feature is not available for cMT Series.For i Series HMI, this feature is only available for firmware version 2...

Switch SW1 to ON position (as shown in picture 1). Press “Reset” or re-plug in the HMI. Picture 1  2. Touch panel calibration screen is shown as follows. Put the HMI screen perpendicularly to your line-of-sight, and point your finger at the center of the cr...

When a large image is displayed, for example, using a 65536 color image as background image may cause the HMI process speed to slow down. Users can follow the instructions below to speed up the display rate of image.  Step 1While using an image file as backgr...

MT8000/6000 OS Image version is 20081013 or later, which supports using USB disk or CF card to update OS. The update process is similar to downloading project to the touch panel HMI. The following example shows how to update OS by using USB disk. 1. Find the c...

The following example shows how to change a MT8070iE (800 x 480) project to an eMT3120 (1024 x 768) project. Step 1. Open the MT8070iE project.Step 2. Click [Edit] button » select [System Parameters] » [Model] tab » select [eMT3120/eMT3150 (1024 x 768)] Step ...

How to translate projects for MT500 model to MT8000/eMT3000 model EasyBuilder provides a feature to translate project files used on MT500 models and download them to MT8000/eMT3000 models. In this way, the project files can be upgraded without being rebuilt. T...

1. Upload the program file of the HMI to the USB disk, and then copy it to the PC (or use the file on the USB disk directly)2. Check out the file that was previously copied from the HMI in the file browser. The original file doesn’t have extension file name. ...

How to display Chinese characters correctly? When you open a project that contains Chinese characters, you may find that the characters are displayed as shown in the following figure The following steps will show you how to solve this problem.Step 1. Go to Sy...

MT8000 provides Ethernet pass-through communication which allows PC to link to the PLC through the HMI. In this situation, the role of HMI is similar to a converter.  First, a virtual serial port must be created on PC. The application program on PC can commun...

The following are the instructions for setting up the printer (take HP printer for example):1. Setup the printer: Run EasyBuilder Pro, select “Edit / System Parameters”; 2. Switch to the “Model” tab, select the printer type: HP PCL Series (USB) and setup the ...

How to download or upload project file by using USB disk or SD card? To download project file from USB disk / SD card to HMI, or upload project file from HMI to USB disk / SD card, please see the steps below.Please note that the described methods are not appli...

MT6000/8000 series HMI provide reliable password protection. The factory initially set password to six 1’s (111111). Users can setup their own password, as follows: 1. Click the “<” icon on the down-right corner, and the status bar will appear. Click “Setting”...

Screen capture is always required for users to edit manual guide. There are two ways of capturing the simulation screen display:A. Capture screen on PC;B. Use “Screen hard copy” function of EasyBuilder Pro: A. Capture screen on PCDuring on-line simulation or o...

1. Built-in MPI with 187.5K baud rate function is available on all of the MT6000i, MT8000i, MT8000X and WT series models.(Note! On the MT6000i, MT8000i, MT8000X series, only the version 2 (V2 / H2) can support the function.) 2. To select SIEMENS S7/300 MPI dri...

This FAQ introduces how to decompile .exob file to .emtp file, and then edit the file in EasyBuilder Pro.  Step 1. Run EasyBuilder Pro, and click [Tool] » [Decompile]. Step 2. When the Decompile dialog box pops up, click [Browse] and choose an .exob file. Des...