Advanced Search
Search Results
904 total results found
3. SPECIFICATIONS
3.1.ROBOT CONFIGURATION (Note 1) During short distance motions, the axis speed may not reach the maximum value stated. The maximum speed is measured at zero position of the robot, and will be limited by the position of other axes.(Note 2) When the rob...
4. EQUIPMENT INSTALLATION TO THE ROBOT
4.1.FLANGE DIMENSIONThis section describes the mounting face dimension of the end effector. Consider the depth of the screw holes and pin holes sufficiently before choose the length of the bolts and pins. Antirust measures of screws, grippers, etc., should be ...
5. CHECK AND MAINTENANCE
Before performing any maintenance, be sure to read SAFETY PRECAUTIONS and understand the content. 5.1.DAILY CHECKSCheck the items below before daily operation as occasion demands 5.2.PERIODIC CHECKS AND MAINTENANCECheck the items at the intervals recomme...
6. CALIBRATING
6.1.INTRODUCTIONCalibration associates the angle of each robot axis with the pulse count value supplied from the absolute Pulsecoder connected to the corresponding axis motor. To be specific, calibration is an operation for obtaining the pulse count value, cor...
7. TROUBLESHOOTING
Be sure to read SAFETY PRECAUTIONS and understand its contents before any maintenance. 7.1.TOOLSTroubleshooting tools includes travelling crane, forklift, internal hexagonal wrench, monkey wrench and special tools for removing the bearings. 7.2.TROUBLESHOOTIN...
APPENDIX
APPENDIX A BOLT TORQUE LIST APPENDIX B SPECIFICATIONS OF CHEMICAL BOLTS APPENDIX C Part list for ER270-2850-CE /ER280-3200-CE APPENDIX D Part list for ER350-3200-CE APPENDIX E Part list for ER500-2800-CE /ER350-3300-CE APPENDIX F Part list for E...
ESTUN- General Lerge Peyloads Series Robot Body Operation Instructions
SAFETY
This chapter describes the precautions which must be followed to ensure the safe use of the robot. Before using the robot, be sure to read this chapter thoroughly. ESTUN robots must be transported, mounted and operated in accordance with national laws, regulat...
PREFACE
This manual describes the following manipulators. Related manuals
1.TRANSPORTATION AND INSTALLATION
Turn each axis to transportation gesture before move the robot and be sure to keep the gesture during transportation until it be properly installed and mounted. Transportation gesture of each axis is shown below. Perform the transportation properly, or it may...
2. CONNECTION WITH THE CONTROLLER
The figure below shows the cables connect the robot with the controller. Connect these cables on the back of the base.
3. SPECIFICATIONS
3.1. ROBOT CONFIGURATION (Note 1) During short distance motions, the axis speed may not reach the maximum value stated. The maximum speed is measured at zero position of the robot, and will be limited by the position of other axes.(Note 2) When the ...
4. EQUIPMENT INSTALLATION TO THE ROBOT
4.1. FLANGE DIMENSIONThis section describes the mounting face dimension of the end effector. Consider the depth of the screw holes and pin holes sufficiently before choose the length of the bolts and pins. Antirust measures of screws, grippers, etc., should be...
5. CHECK AND MAINTENANCE
Before performing any maintenance, be sure to read SAFETY PRECAUTIONS and understand the content. 5.1. DAILY CHECKSCheck the items below before daily operation as occasion demands 5.2. PERIODIC CHECKS AND MAINTENANCECheck the items at the intervals recommen...
6. ZERO CALIBRATING
6.1. INTRODUCTIONCalibration associates the angle of each robot axis with the pulse count value supplied from the absolute Pulsecoder connected to the corresponding axis motor. To be specific, calibration is an operation for obtaining the pulse count value, co...
7. TROUBLESHOOTING
Be sure to read SAFETY PRECAUTIONS and understand its contents before any maintenance. 7.1. TOOLSTroubleshooting tools includes travelling crane, forklift, internal hexagonal wrench, monkey wrench and special tools for removing the bearings. 7.2. Troubleshoot...
APPENDIX
APPENDIX A BOTL TORQE LIST APPENDIX B SPECIFICATION OF BOLT APPENDIX C Part list for ER100B-3000 APPENDIX D Part list for ER100B-3500-DW APPENDIX E Part list for ER130B-3200 APPENDIX F Part list for ER160B-3200 APPENDIX G Part list for ER170B...